Full story: Daily Mail - 'Incompetent' plumber causes gas explosion

A 32-year old plumber is currently in court after he caused a gas explosion which resulted in a home being 'blown from its foundations' and leaving the couple inside with serious burns.

While converting the former kitchen of Martyn Moody and his wife Theresa's luxury home in the Lincolnshire Wolds into a dining room, plumber Daniel Hickling cut off and capped the protruding gas pipe, burying it under the floorboards. However during the work he punctured the pipe and failed to carry out a straightforward check to ensure there had been no damage to it.

Later the couple smelt gas and began searching their home. During this time Mr Moody flicked on a cigarette lighter and the flame ignited, causing a massive explosion with such force that the entire building moved an inch. Mr Moody, a retired construction and electrical tradesman spent two weeks in hospital undergoing skin grafts after suffering serious burns to his hands, arms and scalp. His wife suffered burns to her legs and feet but was released from hospital after two days.

The home, which the couple had built for themselves in 1993, sustained so much damaged that it had to be almost completely rebuilt. It was a year before the couple were able to move back in. They were also left £100,000 out of pocket after being found to be underinsured on their contents insurance and thus had to cover some of the loss themselves.

Lincoln Crown Court were told by prosecutor James Puzey that Hickley was "incompetent to carry out this work and it was carried out incompetently. That led directly to an explosion which almost destroyed the property and caused serious injury to the householders." It was also revealed that he was not a registered Gas Safe engineer and failed to tell the couple this when he agreed to do the work. However he claims that he did not know he would be working on a gas pipe and as such never put himself forward as properly qualified.

Hickley has admitted to breaching the 1998 Gas Safety Regulations and performing work to an inappropriate standard. Recorder Helen Malcolm QC has adjourned the case to a future date when she will give her ruling on the case following these two days of evidence.

-----

Cases like this are a prime example of why having the right qualifications to do the job is vital. Simply having plumbing qualifications is not enough if you are potentially going to work with gas pipes, as not only are you breaking the law and could potentially face prosecution but you are also endangering the lives of your customers. If you train as a gas engineer, becoming Gas Safe Registered isn't just advised, it is essential proof that you are legally competent to work with gas pipes and gas appliances safely. If you are a plumber and would like to learn more about gas engineering, gaining the qualifications required to be elligable for Gas Safe registration, we at Access Training offer comprehensive gas courses to ensure you are fully trained. To find out more click the link or give us a call on 0800 345 7492.

The Department of Energy and Climate Change (DECC) today released the latest Green Deal statistics, and already there has been warnings coming from various different groups and companies.

Insulation company Knauf has warned that according to the current rate, it will take more than 200 years to reach the Government’s 2020 targets. This comes following the revelation that only 2031 more Green Deal assessments place in April than March, suggesting that interest may already be starting to stagnate.

Northern Europe Knauf Managing Director John Sinfield said: “These figures confirm the industry’s worst fears – that the Green Deal has been strangled at birth by the complete lack of any real incentive to encourage uptake amongst householders. If this rate of activity evens out at 10,000 assessments a month it will take 116 years to reach the original DECC aspiration of tackling 14 million homes – and that assumes an optimistic 100 per cent conversion rate from assessment to Green Deal. At a more realistic rate of 50 per cent it will take 232 years to achieve this goal!

“Therefore, our argument to Government is that a significant ‘demand driver’ is urgently needed in order to create momentum amongst householders. The Government claims that the Green Deal is a market driven mechanism yet as currently designed it will only appeal to a small subset of the population. The Green Deal must be made attractive to ALL householders if it is to stand any chance of success. Cashback should be broadened from just Green Deal to all boiler and insulation retrofits.”

However the slow-down in progress could be due to a “severe shortage” of building companies registered as installers, says The Federation of Master Builders in an unrelated assessment based on the same set of statistics. With only 942 companies approved to carry out the work, the FMB has warned that this is nowhere near enough to deliver targets.

Chief executive Brian Berry said: “There are more than 240,000 companies in the construction industry that employ fewer than 14 people. These companies are often best placed to carry out Green Deal work, but because it is difficult to access the market, they are reluctant to train the number of approved installers needed to retrofit Britain’s building stock.

“The Green Deal has now been open for business for almost four months and demand for work under the initiative appears to be growing, but it still feels like a missed opportunity to the majority of SMEs in the industry who haven’t seen any sign of transformation in the energy-efficiency market.”

In order to combat this, the FMB plan to introduce a “Strategy for the Low Carbon Building and Refurbishment Market”. This will involve giving its members better access to the training and certification required to carry out these areas of work.

Sources: Knaufinsulation.co.uk

theconstructionindex.co.uk

Just over a month after the announcement that the start of the Renewable Heat Incentive would be delayed until Spring 2014, the UK Government has also delayed the introduction of proposed "smart meters" to 30 million homes until Autumn 2015.

The £11.7 billion project has been considered vital to getting householders to cut their energy use as the country faces having to import more energy in the future. These smart meters record consumption of gas and electricity in hourly intervals, regularly communicating the information back to the utility provider for monitoring and billing purposes. While the project is set to start in 2015, its estimated that the move to install these into every home won't be completed until 2020.

Angela Knight, chief executive of Energy UK, noted that installing these meters is going to be a "complex task" and this delay will allow the changeover to happen more efficiently. She said: "We welcome the government's prudent decision to allow an additional 12 months to complete the smart meter programme. This recognises the scale of the programme and the need to prepare carefully."

Energy Secretary Ed Davey added: "Completing the national rollout will be an enormous logistical and technical challenge for the industry. Getting this right for consumers is the government's priority."

However the Government will be taking measures to speed up the introduction despite delays. From the end of 2013, when a customer switches from a supplier who has provided them with a smart meter, the new supplier has to either rent the previous supplier’s meter or install their own smart meter, helping to gradually phase out old equipment. This also makes sure that suppliers don’t lose out when they become early adopters. There are also proposals to require energy suppliers and network operators to comply with the Smart Energy Code and ensure their smart meters really perform their advanced functions and supply data to customers.

Further reading: http://www.bbc.co.uk/news/business-22480068

http://www.techweekeurope.co.uk/news/smart-meter-roll-out-delayed-until-autumn-2015-116011

http://www.ft.com/cms/s/0/70d66e86-b97b-11e2-bc57-00144feabdc0.html#axzz2TFaAEogR

While there will always be a demand for qualified tradesmen such as electricians, plumbers and gas engineers, setting yourself apart from the other tradesmen in your local area is an important factor is getting your name out there among potential clients. And the best way to do this is to consider qualifying in more than one skill. Commonly gas engineer training goes hand in hand with plumbing qualifications, but there are far more potential combinations that could benefit your future career.

For example, if a plumber were to undertake electrical training it would open up a variety of new work for them that they wouldn’t be able to complete otherwise without a second tradesman. They would be able to properly install power showers, and by achieving a Part P qualification would also be permitted to sign off the work themselves once they had joined a relevant Competent Person Scheme.

In turn, if an electrician had plastering qualifications, they could provide a fresh finish to a wall surface after tearing it apart to complete an installation. The same applies for combining plastering, tiling and/or carpentry courses. You’ll be increasing both your eternal potential and boost your chance of success when starting up your own business.

Take note though, it’s vital that you train properly for your second skill just as you did the first. A plumber should not be attempting any electrical work without the proper electrical qualifications and the same goes for any other potential trades. Not only would you be putting yourself at risk, but your customer as well. By training properly, you’ll be able to do the job properly and known as a tradesman capable and competent enough to get the job done on their own.

If you would like to find out more about the multi-skills training routes available to you, give Access Training a call on 0800 345 7492 and our team will be happy to tell you more.

Choosing to make a complete career change is difficult at any time of life. There are many factors to take into consideration – what opportunities are there? What training courses will I need to attend? How available is the work and how long will it last?

Take for instance many construction trades (bricklayer, carpenter, plasterer, tiler etc.). At this given time work is pretty slack in the construction industry, but I firmly believe that it won’t last much longer. So now is a good time to begin training for new skills. As soon as the construction industry opens its doors again, there will be a definite skills shortage. Having decided to take the challenge and change career what can you expect to be doing on a daily basis?

Take the plastering trade as an example, which provides plenty of opportunity to work both inside or outside. The weather in this country is not the best, so having the chance to work indoors is an added bonus; you will be working most days and won’t be losing money. Plastering covers more than just “plastering” a wall, it could be screeding a floor, plaster boarding a ceiling, dot & dab on walls, dry lining a wall, the list goes on. This is all internal work, whereas dashing, fine down, K render are all external.

Are there any transferable skills you could use, depending on your background? Plastering involves calculating quantities for mixes etc. so numeracy skills would be an advantage. A lot of questions are asked in the workplace so good communication skills would help, the ability to work unsupervised is a great asset to have, as a lot of the time you are given work and be expected to carry it out unsupervised to a high standard.

So having trained for your new career, what qualifications do you need for the construction industry? An NVQ in a relevant trade is essential; this will allow you to apply for a CSCS card – a must have to work on building sites.

Tomorrow in part 2 I will discuss what training courses are available to you, as well as their cost, duration and what you can expect to learn. Also included will be what prospects are open to you and potential wages upon completion.

- Richard James

Loft insulation is an excellent means of helping to save energy and prevent heat from escaping from our homes. With high cost of fossil fuels in today’s economic climate, and these fuels progressively running out, we shouldn’t be so frugal by putting things in the loft after the extra thickness has been added. After all, just because we might not have paid to have it installed doesn’t mean we should ignore the purpose for which it is intended for - TO SAVE US MONEY! Not only that, but to save on the resources which are only getting more expensive for energy companies to get at and transport to us. We are all guilty of storing things in the loft, and surely these items are not really needed if they’ve been put away from view?

The loft is not an ideal temperature-controlled space in our houses and we are endangering things that could be damaged by the cold and moisture that can form there. Sometimes we have to be brutal with what we are storing and just get rid of it. Let the lagging do the job it’s intended to for and financially you will benefit once your loft has been lagged to the new standards. DON’T put things up there again – your house will stay warmer for longer and you will be happier and wealthier. You also will be reducing your carbon footprint, which is vital to the planet and our descendants for the future. There are a considerable number of ways you can lower your carbon footprint, but many are still quite expensive and take a number of years to pay for themselves. Loft insulation is the cheapest form of energy conservation there is as it’s free to everyone – so why not take advantage of this?

- Mark Lewis

Not all electrical work requires a trained professional. Minor tasks such as replacing a light switch can be performed without having to notify your Local Authority Building Control Department, however they still must be done to current Building and Electrical regulation standard.

While there are a wide variety of different types of light switch you might find in the home (including pull-cord switches, narrow architrave switches and rotary dimmers), here is a guide to the most basic of them – the one-way and two-way switch. The difference between them is that two-way switches are used where there is more than one switch connected to the same light (e.g. at the top and bottom of the stairs).

Safety first

Before you start ANY sort of electrical work make sure the power is switched off at the main consumer unit OR switch off the relevant circuit breaker and lock it if you can. Then make sure that the circuit is indeed dead using a voltage tester/meter. Also take note that since 2006 the core colours inside electrical cables have changed. In the new two-core-and-earth cable, the live or phase core is insulated in a brown sheath rather than red. The neutral core is now blue as opposed to black.

What you will need:

• Voltage tester/meter
• Side cutters Screwdrivers
• Green/yellow earth sleeving
• Suitable replacement plateswitch (1 or 2-way)
• Screws
• Brown PVC electrical tape or sleeving

For one-way switches:

Step 1: Isolate the circuit and then confirm that the power is off using your voltage tester. Unscrew the switch faceplate and pull it forward, revealing the connections behind. These terminals will usually be marked something like L1, L2 and COM.

Step 2: Draw a diagram so that you remember which colour and number of wires were attached to each terminal. Then release the terminal screws and pull the cores from them. If the earth core is properly insulated in green/yellow sleeving and connected to the mounting box, leave this attached.

Step 3: Connect these cores to the correct terminals of the new switch, using your diagram as a reference. Tighten the screws and check they are clamping the cable cores firmly by gently tugging the wires.

Step 4: If there isn’t one already, fit a length of brown sleeving over the blue core to indicate that it is a switched live.

Step 5: If it’s not already fitted, put some green/yellow sleeving over the bare earth core of the incoming cable and connect it to the earthing terminal of the mounting box. If you’re using a metal switch, be sure to earth the switch faceplate as well.

Step 6: Double check that each connection is secure, then push the cable back into the mounting box and fit the faceplate.

For two-way switches:

While this is similar to a one-way switch there will normally be three cores to the cables – coloured brown (formally red), black (yellow) and grey (blue). Again these terminals will be labelled something like L1-3 and COM.

Step 1: Isolate the circuit and make sure the power is off with your voltage tester.

Step 2: Remove the faceplate from the existing switch and disconnect the cable cores.

Step 3: Note which colour goes to which terminal (write it down if you think you’ll forget!) and then transfer them to the corresponding terminals on the new switch.

While this is simply a brief guide to some of the electrical work you can do yourself around the home, more technical electrical work will require you to have a Part P qualification if you wish to carry it out yourself. If you are interested in learning about more work you can do or achieving Part P qualification then the best way is to learn from one of Access Training’s comprehensive electrical training courses. Offering professional qualifications to both aspiring and existing electricians as well as DIY courses, there truly is something for everyone regardless of age, gender, background or experience.

Contact Access Training on 0800 345 7492 for more information or to arrange a visit of our training facilities.

Not everyone needs an extensive plumbing course to know the rights and wrongs of the trade, but with all the DIY products that are for sale in various outlets, there is good information available to prevent water contamination by misconnection of sanitary and waste water from dishwashers, washing machines and such. However, the majority of people don't ask for this advice so not to seem ignorant or feel embarrassed about not know how or what is the right way to do things.

With the economic climate the way it is, the vast majority of people also cannot afford a tradesman with the correct knowledge to do the work properly. There are the unscrupulous people who pretend to be a qualified tradesman, undercut a price just to get the work and don't really care about the consequences of their actions.

Then the poor misguided home owner gets the backlash from the relevant authorities when the source of the contamination is traced back to a particular home. It's very hard to educate people that asking for advice is not showing ignorance. It would only show their concern for doing it the correct way and the people who would give that free information would be only too happy to give them without making them feel humiliated or stupid.

But that's human nature, and people only employ a tradesman when they have that spare amount of money to get the job done. I'm sure the vast majority of people would like to think that any work done to the correct standards without causing problems as rivers and streams being polluted to the degree that is being reported by the water authorities, but unfortunately it always comes down to money.

- Mark Lewis

Although Part P Building regulations require a qualification to undertake extensive electrical work in your own home, minor tasks such as replacing damaged sockets or light switches can be done without having to notify your Local Building Authority Control Department. In this post we'll take you through a few simple steps to replace a plug socket or alternatively change a single one into a double.

Safety first

Before you start ANY sort of electrical work make sure the power is switched off at the main consumer unit or switch of the relevant circuit breaker and lock it if you can. Then make sure that the circuit is indeed dead using a socket tester. Make sure to also have protective gloves and safety goggles on you at all times.

Also take note that since 2006 the core colours inside electrical cables have changed. In new two-core-and-earth cables, the live/phase core is insulated in a brown sheath as opposed to a red one and the neutral core is now blue rather than black. If you are connecting old and new cables together, take extra care to make sure that the cores are attached by their corresponding colours.

What you will need:

• Socket tester & socket template
• Screwdriver
• Pipe and cable detector
• Drill
• Socket faceplate or new double socket
• Wall plugs and screws
• Mounting box
• Green/Yellow pvc sleeving

To change a damaged socket:

To change a single flush socket to a double: